Product ID:POLYLITE 32-737
MSDS Date:01/01/1985
FSC:9330
NIIN:00N000716
MSDS Number: BCGCW

Cage: DO591

Telephone: 800-275-6353

Cage: DO591

UNSATURATED POLYESTER

Fraction By Weight: >50%

Effects of Overexposure:STYRENE AT 400PPM/STRNG CONC: IRRIT COMPLT RESP
TRACT, EYES. AT 10000PPM: POSS FATAL. SOMEWHAT ANES

First Aid:REMOVE FROM EXPOSURE - MAKE COMFORTABLY WARM - USE OXYGEN OR
ARTIF RESP AS REQD. SKIN: WASH THOROUGHLY W/ SOAP & WATER. INGEST:
CONSULT MD. EYE: FLUSH PROMPTLY W/ COPIOUS AMTS OF WATER FOR 15 MIN
& CO NSULT PHYSICIAN.

Flash Point:65F
Lower Limits:1.1
Upper Limits:6.1
Extinguishing Media:FOAM, C0*2, DRY CHEMICAL
Fire Fighting Procedures:NONE - FIGHT LIKE A FUEL OIL FIRE
Unusual Fire/Explosion Hazard:STYRENE WILL POLYMERIZE AT ELEV TEMP,
I.E. FIRE. IF THIS OCCURS IN CLSD CANS POSS VIOLENT RUPTURE.

Spill Release Procedures:REMOVE SATURATED CLOTHING PROMPTLY & WASH
AFFECTED SKIN W/ SOAP AND WATER. REMOVE ALL SOURCES OF IGNIT.
VENTILATE AREA. ABSORB W/INERT MATERIAL AND PLACE IN CLSED CONTNR
FOR DISPOSAL AS SOLID WASTE.WA SH AREA WELL W/TRISODIUM PHOSPHATE &
WATER

Handling and Storage Precautions:STORE & HANDLE AS NFPA CLASS I-C FLAM
LIQ. STORE BELOW 27C (80F) IN A CLSD CAN & DRY AREA TO AVOID
SPOILAGE. OPEN DRUMS SLOWLY; RELIEVES INTRNL PRS
Other Precautions:IN BULK STORAGE CHECK VENTS & FLAME ARRESTORS FOR
PLUGGING BY THE FORMATION OF POLYMERS. GROUND ALL CONNECTIONS,
CONTAINERS, ETC. WHEN USING. SEE SUPPLEMENTAL DATA.

Respiratory Protection:UP TO 100PPM,NONE. 100PPM & ABOVE,NIOSH/MSHA
APPRVD RESP PROTECTION
Ventilation:GEN DILTN OR LOCAL EXHST TO KEEP BELOW TLV. EXPLO-PRF MOTOR
Protective Gloves:NEOPRENE
Eye Protection:YES
Other Protective Equipment:SAFETY SHOWERS, EYE WASH STATIONS. CLEAN
PROT CLOTHING OFTE
Supplemental Safety and Health
AVOID IMPROPER ADDITION OF PROMOTOR OR CATALYST, MIX EACH SEPARATELY W.
THE PRODUCT, NEVER MIX DIRECTLY TOGETHER. VAP PRES: <5.0. SPECIFIC
GRAVITY: 1.1-1.2. % VOLATILE BY VOLUME; <50.

NRC/State Lic Num:NA
Boiling Pt:B.P. Text:>145C, 293F
Vapor Density:3.6
Evaporation Rate & Reference:<1.0 (N-BUAC)
Appearance and Odor:CLEAR LIQUID, W/ TYPICAL STYRENE ODOR.

Stability Indicator/Materials to Avoid:YES
STRONG ACIDS, PEROXIDES, AND OTHER OXIDIZING AGENTS
Stability Condition to Avoid:SUNLIGHT, OPEN FLAMES, CONTAM AND PRLNGD
STRG ABOVE 100F
Hazardous Decomposition Products:CO,CO*2,LOW MOLECULAR WT HYDROCARBONS
& ORGANIC ACIDS
Conditions to Avoid Polymerization:IMPROPER MIXING,SUNLIGHT,CONTAM,OPEN
FLAME, STORAGE AT 100F

Waste Disposal Methods:RESIN THAT MAY BE MIXED W/ PEROXIDE INITIATORS
PRIOR TO SPILLAGE SHOULD BE MIXED W/INERT FILLER & REMOVED TO AN
OPEN AREA. ALLOW TIME TO GEL AND CURE. DO NOT INCINERATE CLSD
CONTAINERS. DISPOSE LWA F ED, ST AND LOCAL REGULATIONS

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.